Product Center

7*24H Online

We will respond to your inquiry within 24 hours after receiving your inquiry.

viton

Viton vs Nitrile o-Rings: What Are The Differences? | NES

Viton™ vs nitrile o rings. As two of the most commonly used elastomers, both Viton™ and nitrile o rings have some fantastic properties. Both offer excellent compression set and have a wide range of uses in industrial and domestic appliions.

Viton™ Tubing | NewAge Industries

Viton™ Tubing. Known for its resistance to oils and chemicals, this remarkable material retains its good mechanical and chemical resistance properties at extremely high temperatures better than any other known elastomer. Viton is also a standout material in its resistance to weather-related aging and ozone. In fact, samples weathered in

Viton Gaskets & Viton Seals | Gasket Engineering

Viton® gaskets will perform in temperatures ranging from -15° F to + 400° F and up to 500° F at times. Viton® Gasket Material Grades. Viton® A . Known as the commercial grade, it is the most widely used of the Viton ® gasket materials as rubber seals for automotive and aerospace lubricants and fuels. These are industries in which Gasket

Chemical Compatibility Reference Chart

Viton® Viton®* Chemical Compatibility Chart: Check the chemical compatibility of Viton® with various chemicals, solvents, alcohols and other products. Viton fluoroelastomer in general has a high temperature tolerance and chemical resistance rating. It is a synthetic rubber that resists many hydrocarbons, biodiesel, and petro

Viton Rubber | Rubber Materials | Qualiform Custom Rubber

Viton® is a highly fluorinated polymer, so it offers exceptional performance in extremely hot and corrosive environments. It also offers superior resistance to aging, oxidizers, ozone, oils and various chemicals. However, Viton® has limited use in low temperature environments.

Viton | Viton O-Rings

Viton® O-Rings. Phone: (716) 759-3080 E-Mail: [email protected] Viton O-Rings. Viton V91A O-Rings. Viton® (fluorocarbon rubber) has excellent resistance to high temperatures, ozone, oxygen, mineral oil, synthetic hydraulic fluids, fuels, aromatics and many organic solvents and chemicals making it a good choice for an o-ring material.

What''s the Difference Between Buna vs Viton O-rings?

May 30, 2019· Properties of Viton O-rings. Viton is a synthetic rubber and fluoropolymer elastomer that is used in O-rings and other molded or extruded products. It offers the best fluid resistance of any commercial rubber. At high temperatures, Viton retains good mechanical properties compared to other elastomers.

Viton™ Rubber - Thermodyn Global Houston

Thermodyn Global Sealing, where your success is sealed, carries Chemours Viton™ fluoroelastomer which is the most specified fluoroelastomer, well known for its excellent (400°F/200°C) heat resistance and resistance to aggressive fuels and chemicals. Rubber products manufactured in the USA.

Viton Chemical Compatibility Chart

Viton withstands high temperature better than most other elastomers, and retains its good mechanical properties. Oil and chemical resistance are also essentially unaffected by elevated temperatures. Compounds of Viton remain substantially elastic indefinitely when exposed to laboratory air oven aging up to 204°C or to intermittent exposures up

Which is Better Viton or EPDM? - Rubber

Neither Viton nor EPDMis a better elastomer than the other because they each have completely different properties. EPDM material is best known for being the ideal outdoor rubber due to its outstanding environmental resistance properties. Viton, contrastingly, is a well-known fluoroelastomer that is used for highly corrosive or abrasive appliions that are too harsh for …

Vitron-C® - High Potency Iron Dietary Supplement Plus

Talk to your doctor about adding Vitron-C®, a high-potency iron supplement with vitamin C that makes doubly sure you''re protected.

What''s the Difference Between Viton and EPDM Seals?

Feb 14, 2017· Viton is great for use with fuel and other corrosive materials, but that extreme durability is unnecessary when dealing with something harmless like water. If you want to ensure maximum durability under stressful conditions, Viton is the ideal choice. As mentioned earlier, Viton seals hold strong under almost any kind of corrosion and acidity.

What is Viton? A Guide To Viton O Rings - NES

The standard grade for Viton™ is A grade, which has 66 percent fluorine content and is most commonly used in o rings and seals. Viton™ B offers better fluid resistance and Viton™ F is particularly good for resistance to fuel permeation. High performance grades are also available but do discuss with us if you’re not sure what you need.

Viton ™ Rubber — Thunder Technologies LLC

Viton™ fluoroelastomer was developed by the Dupont Chemours Company to meet aggressive fuel and chemical resistance and mechanical properties not available in other elastomers. Viton™ rubber is often the only available seal choice for resistance to amines, caustics, hydrocarbon fluids and ability to maintain a seal at low temperatures.

Viton® vs. FKM | Global O-Ring and Seal

Since Viton® performs better than hydrocarbon rubbers in fluid resistance, blends of other rubbers with Viton® typically perform significantly poorer than 100% FKM. Blends of Viton® with hydrocarbon rubbers do not perform “almost like FKM” or anything close to it. Beware of the “good deal.”. Rather than being a “low-cost

FKM - Wikipedia

Viton® O-rings have an extremely wide temperature range -50°C to +205°/230°C (-15°F to +400°/440°F) Low compression set and low gas permeability. Viton® O-rings have excellent resistance to acids, mineral and vegetable oil and greases, fuels, aliphatic, aromatic and chlorinated hydrocarbons, non-flammable hydraulic fluid and several

VITON™ GF & VITON™ ETP TECHNICAL INFORMATION …

Viton™ made with APA is a proprietary development by The Chemours Company that improves the performance of specialty fluoroelastomers. The following section offers a brief description of Viton™ polymers that provide FDA compliance and their unique capabilities. • Viton™ GF-600S is a high-fluorine, peroxide-cure type of Viton™. Compared to

Viton® and EPDM - What is the Difference? | Polymax India Blog

Feb 05, 2016· Viton® rubber is a fluoro elastomer, whereas epdm rubber is ethylene-propylene-diene-monomer. The primary differences between Viton® and EPDM is in their chemical resistance and temperature ranges. Both have different properties and appliions for …

VITON: An Image-Based Virtual Try-On Network

VITON consists of two stages: (a) an encoder-decoder generator stage (Sec 3.2), and (b) a refinement stage (Sec 3.3). ios. Moreover, without injecting any person representation or explicitly considering deformations, it fails to generate photo-realistic virtual try-on results. 3. VITON The goal of VITON is, given a reference image I with

Viton™ High-Performance Fluoroelastomers

Products made with Viton™ fluoroelastomers retain their flexibility, shape, and seal when exposed to chemicals and high temperatures. Viton™ FreeFlow™ extrusion process aids also improve processing, increase output, and reduce waste. Featured Industries. Demanding environments require components that can perform without downtime or breakdown.

What is a Viton® (FKM) Gasket & What are its Appliions?

Apr 12, 2019· Viton® A. Viton® A dipolymers are polymerized from two monomers – vinylidene fluoride (VF2) and hexafluoropropylene (HFP). It is the most widely used Viton® gasket material and has appliions as rubber seals for aerospace and automotive lubricants and fuels. Viton® B

Viton Rubber Parts & Products - Timco Rubber

Viton rubber, a specific fluoroelastomer polymer (FKM), was introduced into the aerospace industry in 1957 to fulfill its needs for a high-performance elastomer. Following its introduction, the usage of this material spread quickly to other industries. These days, Viton seals, o-rings, and others rubber parts are now used regularly in the

4 Common Misconceptions About Viton or FKM Rubber | Hot Topics

Jul 03, 2014· Viton B-600 – B type polymers have higher fluorine content than A types. Higher fluorine content typically adds more chemical resistance to the rubber compound. Viton GF-600S – Considered an APA polymer, this is high fluorine and peroxide-cured. F type polymers have even more fluorine content than B types.

What is Viton | Advantages of Viton | What is Viton rubber

May 10, 2016· What is Viton® rubber used for? As we have mentioned previously, Viton® is a durable material for O-rings, gaskets and seals, all of which can be specified and manufactured here at Martin’s Rubber; either to your own bespoke requirements or as off-the-shelf parts. Viton® tubing is also commonly used in automotive, and other transportation

Viton - an overview | ScienceDirect Topics

The Viton O-ring withstands a condition of 230 °C × 24 h. Viton is a common name for the copolymer of hexafluoropropylene and vinylidene difluoride. The material designation given by the ASTM to this copolymer is FKM. The quality standard of the O-ring used for the closed cell is JIS (the Japanese Industrial Standard) B 2401-4D-p-12.5.

The Viton A-Type Fluoroelastomers

Viton A, is the easiest processing (i.e., extrusion, calendering) of the three, and is particularly good for use in highly extended stocks. Viton A-HV is a high-viscosity analog of Viton A and gives vulcanizates having the highest tensile strength and best resistance to compression set. Handling Precautions Using recommended handling procedures

Viton Gaskets, O-Rings and Seals - Seal & Design, Inc

Mar 07, 2019· Fluorocarbon rubber (FKM Viton ®) has excellent resistance to high temperatures, ozone, oxygen, mineral oil, synthetic hydraulic fluids, fuels, aromatics, and many organic solvents and chemicals.It has a higher resistance to swell in high octane and oxygenated fuel blends. Low-temperature resistance is normally not favourable and for static appliions is limited, …

Viton / FKM | O-Ring

What Does The Name Vito Mean? - What Does My Name Mean

VITON® Fluorelastomers An overview - Rubber Technology

Viton® is the only choice. Genuine Viton® is manufactured with 100% pure fluoroelas-tomers and is certified with the Viton® certifie, which is granted by DuPont Performance Elastomers. ERIKS was appointed licensed distributor for Genuine Viton® products in 1994. In 1999, our license was renewed.

EPDM vs. Viton: Which Material is Right for Your Parts

Mar 11, 2021· Viton is made to thrive in these types of situations, as it is highly resistant to chemicals and other difficult substances. For example, Viton is often used to make gaskets used in slurry appliions where offgassing poses problems for other materials. Viton is also better for extreme temperatures, with an operating temperature range of up to